Pianos routinely make movers yearly list of products that are most often damaged. Grand pianos are specifically troublesome. Practicing the following treatments for taking apart, padding and filling grand pianos will prevent damage, lower claims expenditure, and improve consumer fulfillment.
1) At least 3 people are needed to deal with a child grand piano. If the child grand piano needs to increase or down stairs or if a full or performance grand piano needs to be transported, a minimum of four individuals are needed.
2) Always complete a precise and thorough inventory. It might be more effective or necessary to utilize a visual stock to properly describe and reveal pre-existing damage.
3) As numerous parts are dismantled, please location all hardware in an appropriately identified parts bag and after that place the parts bag in a "Parts Box".
4) Remove the music rack (lyre) from its track by pulling it towards the keyboard. Wrap it in a tidy furnishings pad.
5) Disconnect the lid by removing the hinge pins. Have a single person wiggle the cover, holding it opposite the hinge, while a 2nd individual works the pin loose. Please be careful not to damage the wood with the pliers or with the pin itself. If necessary, cover the jaws of the pliers with a little fabric to assist prevent damage to the wood. Wrap the cover in a tidy furniture pad.
6) Get rid of the prop that holds the cover open and wrap it in a tidy furniture pad. The prop has a hinge pin and is in 2 pieces.
7) Eliminate the pedal assembly and wrap it in a tidy furniture pad. The braces at the rear of the assembly rest in slots at each end. When getting rid of the screws, please be careful not to drop the braces. In addition, please be specifically cautious with the push-rods so that they will not get bent. As you face the piano, number the push-rods from delegated right as "1", "2", and "3", by placing a piece of masking tape with the proper number on each rod. Note: If masking tape is unavailable, please usage correctly identified parts bags for this purpose. When reassembling at location, please be sure to put the rods in the right order so that the pedals will work properly.
8) Pad the piano by placing a clean rolled furnishings pad (stretch-wrap the pad to avoid it from unrolling) on the cover of the keyboard to avoid it from flopping open while you handle the piano. Cover the top of the piano with two tidy furniture pads, neatly folded around the keyboard. Use rubber bands to secure the pads. Keep in mind: Please make sure that the surface area of the piano is dust-free before padding it. Padding a highly refined surface area that is dirty might trigger fine scratches, particularly on a black lacquer surface.
9) Position a piano board and attach the straps so that it is ready to get the piano. The raised brace on the piano board need to be at the keyboard end of the piano.
10) Get rid of the left front leg by placing one person beneath the piano at the left end of the keyboard. The other two people should support the left front corner. The individual beneath the piano must turn the retaining block so that the long end points far from the leg. The screws, if there are any, need to then be gotten rid of. The "beneath" person must then get out from under the piano prior to really removing the leg. Make certain to have 2 individuals lifting the corner of the piano while the third individual gets rid of the leg. Note: Please make certain to note which legs were eliminated from which positions since some pianos have legs that are not interchangeable.
11) Location the piano on the piano board by decreasing the "leg-less" end onto the board. Please be sure to raise the whole piano a little while finishing this maneuver to avoid excessive pressure on the staying, connected legs as the piano pointers. Be sure that the piano is focused snugly against the brace at the end of the piano board.
12) Remove the two remaining legs and wrap them in clean furnishings pads. view publisher site These legs are held in place by a "key and slot" plan. To get rid of the leg, slide it inward towards the center of the piano up until it comes out of the slot.
13) Protect the piano to the piano board by bringing completions of the straps together and securing them. Place folded burlap pads over the furnishings pads but under the straps to provide extra security to the edges of the piano. To prevent the strap near the narrow end of the piano from slipping off, connect the loose ends of the two straps together.
14) To move the piano over a flat, level surface, tilt the piano and piano board and location a four-wheel dolly under the center of the piano board.
15) To move the piano up or down stairs, use the piano board as a skid. After adequately padding the stairs for security versus home damage, place the keyboard end of the piano toward the bottom of the stairs. Connect a bulge strap to the top end of the piano board to avoid the piano from slipping.
16) To load the piano, leave it on the piano board and location it in a tier as the very first base item with the keyboard dealing with the wall of the preceding tier. The best location to load the cushioned lid is in between the piano and the preceding tier or in between the piano and the wall.
Although grand pianos represent a significant difficulty, they can be moved without damage by utilizing sound judgment and practicing the procedures noted above.